piston clearance
英 [ˈpɪstən ˈklɪərəns]
美 [ˈpɪstən ˈklɪrəns]
网络 活塞余隙; 汽缸余隙; 活塞间隙
双语例句
- Study of composite piston top construction and clearance of each contact face
组合活塞顶部结构及各接触面间隙的研究 - Piston to head clearance
活塞底和气缸头间隙 - Also the influence of piston impact force are discussed which including engine rotate speed, piston pin offset, clearance between piston and cylinder, piston mass and contact strength of piston surface.
并分别讨论了发动机转速，活塞销偏置量、活塞与气缸的间隙量、活塞质量以及活塞表面接触刚度对活塞碰撞冲击力的影响。 - New Method of Measuring Piston Ring End Gap Clearance with line Matrix CCD
线阵CCD检测活塞环闭口间隙的新方法 - There are many advantages for the new method of noncontact measurement employing the sensor for measuring piston ring end gap clearance dimension.
用其检测活塞环闭口间隙尺寸，是一种新的非接触式测量方法，具有许多优点。 - The main content of the thesis is as follows: 1 、 Summarize essence rules of piston pin boss configuration and pin bore surface design, including horizontal and vertical profile rules of pin bore, analyze and specify the definition method of pin bore fitting clearance.
总结了活塞销孔结构以及销孔表面设计的基本规律，包括销孔的横向形线规律和纵向形线规律两个方面，并分析说明了销孔配合间隙的确定方法。 - And the influence of several important factors to leakage of ball piston pair ( clearance between ball piston and rotary cylinder block, pressure of working oil and speed of cylinder block etc.) was analyzed.
分析了各种重要因素如球活塞与旋转缸体缸筒间隙、工作油液的压力以及缸体转速等对球塞副泄漏量的影响。 - Several groups of supporting cavity and damping orifice were set on the circular surface of piston so as to adjust the pressure in the clearances by stiffness of pressure adjustment when load varies and then to keep the even clearance for avoiding chucking.
该结构在柱塞的圆周表面上设置了几组支承腔室和阻尼小孔，构成的静压支承结构具有间隙中压力可随间隙变化的调节刚度，保证间隙大小的均匀性，避免卡紧。 - Among refrigerant leakages are caused by clearance fit in rolling piston compressors, the maximal amount of leakage is occurred in the radial clearance, which is mainly processed by the mode that the refrigerant dissolves into the lubricant.
在滚动转子式压缩机内由于间隙配合造成的制冷剂泄漏中，转子径向间隙的泄漏量最大，它主要是以溶于润滑油的形式泄漏的。 - In the design of pistons, the leakage from clearance between piston and cylinder had been calculated by MATLAB and then the clearance was chosen as 6~ 10 μ m.
在柱塞的设计中，用MATLAB软件对柱塞和缸孔间的泄漏进行了仿真分析，在综合考虑了泄漏量和合作单位加工能力的情况下选取柱塞和缸孔间隙为6～10μm； - Then the piston clearance is mainly discussed due to its affecting the performance of a damper.
讨论了活塞间隙对磁流变减振器工作性能的影响规律，得到了活塞间隙的取值范围及依据。 - This article believes that clearance space has the most important effect upon the ventilation of the piston compressor, and introduces the method of measuring and adjusting the clearance space.
认为余隙间隙对活塞式压缩机排气量的影响最大，并介绍了余隙间隙的测量及调整方法。 - The cracking of big diameter fuel droplet and the combustion of the overflowing gas from the combustion chamber at low temperature in the piston crown clearance are the main reasons of soot emission from diesel engine.
富油区大直径油滴的燃烧裂解和活塞顶隙处外溢燃气的低温燃烧是柴油机产生碳烟微粒排放的主要原因。 - This paper relates the measuring principle of measurement system for tangent elasticity of piston ring, method of measuring data processing, optimun fitting method of least square line for tangent elasticity when piston-ring arrived in close clearance.
论述了活塞环切向弹力测量系统的原理、测量数据处理方法、切向弹力与开口间隙变化的最小二乘直线拟合方法、活塞环开口闭合点和活塞环达到闭口间隙时的切向弹力的评定。 - In rolling piston compressors, clearance fit is adopted between rotor and cylinder. Its leakage passages are pressurized by oil films.
在转子压缩机内转子和气缸之间采用间隙配合，其泄漏通道通过油膜来密封的。 - A new hydraulic hammer was simulated. Performance of the new hydraulic hammer is affected by vary technical parameters, such as diverse input flux, diverse piston radius clearance, diverse valve radius clearance, diverse oil temperature.
通过对一种新型液压锤进行建模与仿真，得到了不同的输入流量、活塞半径间隙、换向阀半径间隙、温度等技术参数对液压锤性能的影响。 - The results show that the leakage losses of rolling piston compressor can be reduced effectively by designing the value of leakage clearance rationally.
结果表明，合理地设计转子径向配合的间隙值，可以有效地降低转子压缩机的泄漏损失。 - The automatic piston ring end gap clearance sorting machine developed according to this principle possesses features of simple construction, complete function, easy adjustment and operation and high anti interference ability.
按此原理研制的活塞环闭口间隙自动分选机，具有结构简单、功能齐全、调整和操作容易、抗干扰能力强等特点。 - The secondary motion characteristic of piston was improved by adjusting piston pin offset and clearance between piston and cylinder liner, as well as optimizing piston skirt profile.
通过调整活塞销偏置、配缸间隙和优化活塞裙部型线来提高活塞的二阶运动性能，结果表明原有的中凸桶形裙部型线能够保证良好的活塞运动特性。